Send us a text

By providing your phone number, you consent to receive calls and transactional/informational text messages (SMS) from First Layer, powered by Topline Pro, including calls and messages made using AI-powered technology. You can unsubscribe at any time by replying STOP. Message and data rates may apply. Message frequency varies.

By submitting this form, you agree to our Terms of Service & Privacy Policy.

First Layer, New York

Where Peelable Coating Doesn't Go

First Layer applies temporary surface protection to finished surfaces in New York buildings. A few surfaces are not coated directly. Here is the full list, what we use on each one, and why.

Surface by surface

What goes on each surface, and what we do instead

Spray-applied protection is our main service, but no single product covers every surface. We choose the protection for the surface, not the other way round.

SurfaceWhat we useWhy
Where we apply Peeltex
Polished marble, terrazzo and polished stonePeeltex Grey or ClearApproved for Peeltex. Historic or landmark finishes get a test patch if the conservator asks for one.
Elevator buttons and operating panels, stainless and doorsPeeltex ClearClear keeps buttons and panels readable.
Elevator cab walls and floors, sills and tracksPeeltex Grey or WhiteWe plan access and moving parts with the elevator contractor.
Coated floorsFine sand or glass dust broadcast into the wet coat, about 1 hour after coatingIt sticks without sinking in, for traction and slip resistance.
Heavy impact routesFelt-back impact board with a sealed Peeltex Grey topBoard takes the impact and the sealed top keeps spills out.
Facade glass and framesPeeltex High Humidity, exterior, about 12 monthsIt is the grade made for exterior exposure.
Interior glass, mirrors and fixturesPeeltex Clear, interior onlyClear is for interior and dry areas.
Paint booths and overspray areasPeeltex WhitePeel it off and the booth is white again.
Stage floorsPeeltex Grey or WhitePaint goes on top, and the film peels at wrap.
Loading docks, dock plates and steel platesPeeltex Grey with fine gritAvoid tight forklift turns, which can tear the film. Tears are easy to repair by re-coating.
Concrete and precastPeeltex High Humidity, after a moisture test on the concreteTest the moisture first, then coat.
Not coated directly
CarpetKoruser or Axiom carpet protection first, then Peeltex over itThe carpet is not coated directly.
FabricsLow tack film or boardPeeltex is not made for them.
Freshly painted surfacesBoard or film until the paint has curedThe film can pull fresh paint off with it.
Bare brick, untreated wood and other porous surfacesBoard, film or mats insteadNot coated directly.
Surfaces in bad shape, such as flaking paintRepair first, or board, film or matsIf paint is flaking, there is no sound surface under it. The film has nothing to hold on to and just peels off.
Heat sources, hot work and high service temperaturesNot protected with peelable filmPeeltex has no published heat rating. Apply after any baking or curing.
Our product rules

Ten rules we do not bend

These apply to every job, whatever the schedule says.

  1. Carpet gets carpet protection first.

    Koruser or Axiom carpet protection goes down, then Peeltex over it. We do not coat carpet directly.

  2. Fabrics, fresh paint, bare brick, untreated wood and porous surfaces are not coated directly.

    We use film or board on these instead.

  3. Elevators: sills and tracks can be coated.

    Grey or White on cab walls, floors, sills and tracks, Clear on buttons and operating panels. We plan access and moving parts with the elevator contractor.

  4. Docks and steel plates: coated with fine grit, with a forklift caution.

    Avoid tight forklift turns, which can tear the film. Tears are easy to repair by re-coating.

  5. Polished marble and polished stone are approved.

    Historic or landmark finishes still get a test patch if the conservator asks for one.

  6. Concrete and precast: High Humidity, after a moisture test.

    We test the moisture in the concrete first.

  7. Floors get grit for traction.

    We broadcast fine sand or glass dust into the wet coat about 1 hour after coating, so it sticks without sinking in.

  8. No published heat rating.

    Peeltex does not go near heat sources or hot work.

  9. Clear is interior only. High Humidity is exterior, about 12 months.

    We match the grade to where the surface is.

  10. Heavy impact routes: felt-back impact board with a sealed Peeltex Grey top.

    Hardboard alone is not the answer. The sealed top contains spills.

Straight talk

Being honest about limits wins the whole building

A manager who hears a plain no from us on fresh paint and bare brick can trust our yes on the marble lobby.

Questions about what we will and will not coat

Why won't you coat fresh paint or bare brick directly?

Fresh paint can lift with the film, and bare brick, untreated wood and other porous surfaces are not coated directly. A surface in bad shape, such as flaking paint, gives it nothing to hold on to, so it just peels off. We would rather tell you that on the site walk than put it down and hope. Carpet and concrete are different: carpet gets Koruser or Axiom carpet protection first, then Peeltex over it, and concrete takes Peeltex High Humidity after a moisture test.

Do you coat polished marble and stone?

Yes. Polished marble and polished stone are approved for Peeltex, and we use Peeltex Grey or Clear. Historic or landmark finishes still get a test patch if the conservator asks for one, and we do not proceed until they are happy with it.

Can it handle forklifts or dropped tools?

Forklifts, yes, with a limit. Loading docks and steel plates can be coated with Peeltex Grey and fine grit, but tight forklift turns can tear the film. Tears are easy to repair by re-coating. Where heavy loads or dropped tools are expected, we use felt-back impact board with a sealed Peeltex Grey top.

What if my surface is not on this list?

Walk it with us. We test a patch on a new surface before we coat it. If a surface should not be coated directly, we will say so and name what to use instead, whether that is board, film or mats. You get a straight answer before any work starts.

Not sure about a surface?

Walk it with us before anything goes down

Tell us what is being finished and when the trades arrive. We will walk the surfaces with you, say what we will and will not coat, and quote the job. We work in New York City, Long Island and the Northeast.