Schools, Offices and Labs: Surface Protection
First Layer builds dust walls and sprays temporary surface protection, so finishes and clean areas come through off-hours work in the condition they went in.
For schools, offices, data centers and labs in New York and the Northeast.
What is protected during off-hours work?
Finishes and clean areas need to be ready again when people return. First Layer protects them during off-hours work with temporary surface protection and built separation, then peels and removes it at turnover.
Spray-applied protection (Peeltex) covers floors, glass, metal and fixtures. Built protection from our carpentry crew separates the work from the clean area with dust and separation walls, zipper doors and sealed openings.
Spaces we protect
Schools
Finished floors, glass and fixtures in rooms and halls that need to be ready for the next day.
Offices
Lobbies, corridors, glass and elevators on routes that stay in use around the work.
Data centers
Clean areas separated from the work with dust walls, zipper doors and sealed openings.
Labs
Finishes and clean areas separated from the work, with the protection removed on a scheduled date.
Dust walls plus surface protection
The lead service for this market is dust walls plus surface protection. Built protection means temporary dust and separation walls, zipper doors and sealed openings, with plywood and board boxes over fixtures and equipment.
Surface protection goes on what stays exposed: sealed hard floors, glass, stainless and finished metals. Add protection upkeep, a weekly or per-visit walk to inspect, repair and re-apply damaged protection, with a short report after each visit.
Per job
Quoted by square foot, linear foot or opening. We quote from what we see at the site walk.
Annual plan
A set number of protection calls per year at a fixed rate, for buildings with recurring work.
Rental
Reusable door guards, corner guards and stair covers, installed and collected.
Product only
Peeltex through Strata Shield Supply, with crew training, if your own crew applies it.
One crew, one point of contact, five steps
Every job follows the same five steps, so off-hours crews know what is protected and when it comes off.
Removal timing is written into every job, so film is not left on past its rated life.
-
Site walk
We walk the affected and unaffected areas with you, mark what gets protected and agree the plan for the job.
-
Test patch on a new surface
Where a surface is new to us or delicate, we test a small patch before full application.
-
Install
We spray and build the protection in the agreed areas.
-
Inspect and log
We inspect the protection, repair what is damaged and keep dated photos by area.
-
Peel and hand over
We peel the film, remove board, clean up and leave the space punch-ready on the scheduled date.
Surface rules for schools, offices and labs
Some surfaces take protection directly and some do not. These rules go into every quote.
What can be coated
- Sealed hard floors, polished marble and stone: Peeltex Grey.
- Interior glass, mirrors and fixtures: Peeltex Clear, interior only.
- Elevator buttons and panels: Peeltex Clear. Cab walls, floors, sills and tracks: Grey or White. See elevator cab protection.
- Carpet: Koruser or Axiom carpet protection first, then coated over it.
What to check first
- Concrete takes Peeltex High Humidity after a moisture test.
- Fine sand or glass dust is broadcast on floors about 1 hour after coating, for traction.
- Loading docks and steel plates can be coated. Forklift tears are easy to repair by re-coating.
- There is no published heat rating, so we apply after any baking or curing.
Where it does not go directly: bare brick, untreated wood and other porous surfaces. We use board, film or mats instead. For lobbies and stone, see lobby and stone protection.
Protection for schools, offices and labs, answered
What does built protection mean?
Built protection is work by our carpentry crew: temporary dust and separation walls, zipper doors and sealed openings, plus plywood and board boxes, corner guards, door and frame guards and floor runners.
Can you protect a clean area during off-hours work?
Yes. We separate the clean area from the work with dust walls and sealed openings, and spray temporary surface protection on the finishes that stay exposed. We confirm the areas at the site walk.
Is there an annual option for buildings with recurring work?
Yes. An annual plan is a set number of protection calls per year at a fixed rate. Jobs can also be quoted per job by square foot, linear foot or opening. See the First Layer packages.
What surfaces are not coated directly?
Bare brick, untreated wood and other porous surfaces are not coated directly, and carpet gets Koruser or Axiom carpet protection first. See where protection does not go.
Walk the space with us before the work starts
Tell us which areas stay clean and when the crews work. We set the walls, the protection and the removal date, then give you a quote.