For elevator contractors and building owners
Elevator Cab Protection in NYC
First Layer protects the walls, doors, sills, tracks and floor of an elevator cab from install to turnover with temporary surface protection. We inspect it during the job and peel it off on handover day.
Book a site walkCall (516) 756-9303
Priced by the job: request a quote or book a site walk. See all ways to buy.
What does elevator cab protection cover?
First Layer protects elevator cabs for elevator contractors, building owners and property managers in New York City, Long Island and the Northeast. We spray Peeltex Grey or White on the cab walls, floors, sills and door tracks, and Peeltex Clear on buttons, operating panels and stainless. Clear is interior only, and a cab interior is exactly that. On the floor we lay the Premium Assembly: felt backed board, felt side down, with sealed Peeltex Grey on the hard plastic top, run 6 inches up the wall. Where a floor is coated for traction, we broadcast fine sand or glass dust into the wet coat about 1 hour after coating, so it sticks without sinking in.
The cab is covered from install to turnover. We plan access and moving parts with the elevator contractor, so every part that has to work keeps working. Sills and door tracks can be coated, and buttons and operating panels get Peeltex Clear while the cab walls and floors are sprayed grey or white. On handover day we inspect, peel the protection off and clean up. The finish underneath is what the owner sees first.
Cab anatomy: what we protect and what we leave alone
A cab is a mix of finished surfaces and moving parts. We protect the finishes. We plan access and moving parts with your elevator contractor.
| Cab part | Treatment | Detail |
|---|---|---|
| Walls | Protected | Peeltex Grey or White |
| Doors | Protected | Peeltex Clear, interior only. We plan access and moving parts with the elevator contractor. |
| Ceiling | Protected | Peeltex Clear, interior only |
| Handrails | Protected | Peeltex Clear, interior only |
| Floor | Premium Assembly | Felt backed board, felt side down. Sealed Peeltex Grey on the hard plastic top, run 6 inches up the wall.Nothing goes between the board and the finished floor. On a coated floor we broadcast fine sand or glass dust into the wet coat about 1 hour after coating, for traction and slip resistance. |
| Sills | Protected | Peeltex Grey or White. We plan it with the elevator contractor. |
| Door tracks | Protected | Peeltex Grey or White. We plan access and moving parts with the elevator contractor. |
| Gibs and door edges | Planned | We plan access and moving parts with the elevator contractor. |
| Call buttons | Peeltex Clear | Peeltex Clear over the buttons, with the cab sprayed grey or white around them, so the buttons stay readable. |
| Operating panels and hall stations | Peeltex Clear | Peeltex Clear. We coordinate access with the elevator contractor. |
Peeltex alone has no impact rating, which is why the floor gets the board. Read more on where peelable protection doesn't go.
Market context
New York is replacing a lot of cabs
NYC public housing alone plans to replace about 271 elevator cabs in 138 buildings, with work starting from the third quarter of 2026. Every new cab is a finished interior that has to reach turnover clean.
Source: City Record notice. This is market context, not First Layer work.
From install to turnover
One crew follows the cab through the job, so the protection is on before the trades are and off when the owner takes over.
Site walk
We walk the cabs with you and your elevator contractor. We agree access, moving parts and when we can get in.
Protect at install
We spray the walls, doors, ceiling and handrails and lay the floor assembly.
Inspect
We check the protection while the other trades work and touch up where it is needed.
Peel on handover day
We peel the protection off, take the floor assembly out and clean up. The cab is ready to hand over.
Elevator cab protection questions
How is elevator cab protection priced?
Elevator cab protection is priced by the job. The number of cabs, the schedule and the access we get change the quote. Request a quote or book a site walk and we will look at your cabs first.
What do you protect inside the cab?
We protect the cab walls and floors with Peeltex Grey or White, and buttons, operating panels and doors with Peeltex Clear, which is interior only. The floor gets the Premium Assembly: felt backed board, felt side down, with sealed Peeltex Grey on the hard plastic top, run 6 inches up the wall. That assembly is what handles dropped tools and heavy loads.
Do you coat door tracks, sills or buttons?
Yes. Sills and door tracks can be coated with Peeltex Grey or White, and buttons and operating panels get Peeltex Clear. We plan access and moving parts with the elevator contractor on the site walk so nothing gets in their way.
When does the protection come off?
It comes off on handover day. We inspect the cab, peel the protection off the walls, doors, ceiling and handrails, take out the floor assembly and clean up. Until then the finishes stay covered from install to turnover, so the owner sees the finish underneath.
Walk your cabs with us
Tell us how many cabs and when they install. We will walk them with you and your elevator contractor, then quote the job. We work in New York City, Long Island and the Northeast.