Send us a text

By providing your phone number, you consent to receive calls and transactional/informational text messages (SMS) from First Layer, powered by Topline Pro, including calls and messages made using AI-powered technology. You can unsubscribe at any time by replying STOP. Message and data rates may apply. Message frequency varies.

By submitting this form, you agree to our Terms of Service & Privacy Policy.

Illustration of a gloved hand peeling a grey protective sheet off polished white marble
Lobby and Stone Package

Marble Lobby Floor Protection in NYC

First Layer sprays peelable temporary surface protection over polished marble, terrazzo and polished stone, all approved for Peeltex. We inspect it through the job and peel it off at turnover.

What it is

How do you protect a marble lobby floor during construction?

A lobby floor is the first thing every visitor sees. It is also the route for tile, drywall, carts and every trade on the job. The Lobby and Stone Package puts a sealed, peelable layer of temporary surface protection over polished marble, terrazzo and finished stone before the work starts. Dust, slurry and scuffs land on the protection, not on the stone.

First Layer sprays Peeltex Grey or Clear, adds impact board on the delivery routes, inspects the floor through the job and peels everything off at turnover. We test a patch on a new surface, and historic or landmark finishes get a conservator test patch if one is requested. You get a photo log, so the condition of the floor is on record from the first day to handover.

The process

From site walk to peel in four steps

We walk the lobby with you first, then protect, inspect and peel.

  1. 1 Polished stone

    Site walk

    We look at your floor, the delivery route and the schedule. Polished marble and polished stone are approved for Peeltex. Historic or landmark finishes get a test patch if the conservator asks for one.

  2. 2 Spray

    Apply

    We spray Peeltex Grey or Clear across the floor. Grey is touch dry in about 2 hours under optimal conditions. Where floor traction matters, we broadcast fine sand or glass dust into the wet coat about 1 hour after coating, so it sticks without sinking in, for traction and slip resistance. Delivery routes get impact board.

  3. 3 Photo log

    Inspect

    We walk the floor through the job, check seams, edges and routes, touch up what needs it and log each visit with photos.

  4. 4 One sheet

    Peel

    At turnover the protection comes up. We remove it, clean up after ourselves and hand the floor back.

If the conservator asks for a test patch on a historic or landmark finish, it comes before the full floor.

Why sealed matters

Sealed, not shifting

Protection that moves, or leaves a gap, can do its own harm to polished stone. Here is the difference we build around.

Hardboard on its own

Can shift and let it in

  • It can shift as people and carts cross it.
  • Seams can open along the joints.
  • Water and dust get underneath.
  • Moisture can sit trapped against the stone.
Sprayed protection

Sealed and contains spills

  • It is sprayed on as one continuous coating.
  • It is sealed to the floor, so it stays where we put it.
  • A spill stays on top until it is cleaned up.
  • It peels off at turnover.
During the job

What we inspect and how often

Inspection is part of the package, not an extra. On each visit we look at:

  • Edges, seams and corners that have lifted
  • Scuffs, cuts and worn spots in the coating
  • Spills, grit and trapped debris on the surface
  • Impact board that has moved at turns and thresholds

Every visit goes in a dated photo log, so you can see the floor at any point in the job. How often we visit is set with you at the site walk and follows your schedule, such as after a big delivery or when a new trade moves in. We do not promise a fixed number of visits.

Delivery routes

Impact board goes where the loads go

Peeltex alone has no impact rating. Where carts, pallets or dropped tools are expected, we lay impact board.

Felt side down on the floor. Peeltex goes on the hard top only. Nothing goes between the board and the finished floor, no coating and no liquid, because board can bond to the floor if it is installed wrong.

Not every surface is coated directly. Carpet gets Koruser or Axiom carpet protection first, then Peeltex over it. Bare brick, untreated wood and other porous surfaces are not coated directly. See where protection does not go.

Book a site walk Bring the floor plan. We walk the lobby and the delivery route together.
Questions

Marble lobby protection, answered

Is it safe to put peelable protection on marble?

Polished marble and polished stone are approved for Peeltex. We test a patch on a new surface, and historic or landmark finishes still get a test patch if the conservator asks for one.

Does the lobby have to close while you work?

We plan the schedule around your building. Peeltex Grey is touch dry in about 2 hours under optimal conditions. The manufacturer does not publish a walk on or full cure time, so we plan the schedule with you at the site walk and do not promise one.

How is the Lobby and Stone Package priced?

Priced by the job. Floor size, delivery routes and the schedule all change the work, so request a quote or book a site walk of your lobby.

Will it hold up to carts and pallets?

Peeltex alone has no impact rating. On delivery routes we add impact board, felt side down on the floor with Peeltex on the hard top only. Heavy loads and dropped tools are what the board is for. Hardboard laid alone can shift and let water and dust underneath.

Walk your lobby with us

Tell us the stone, the route and the schedule. Request a quote or book a site walk.