Send us a text

By providing your phone number, you consent to receive calls and transactional/informational text messages (SMS) from First Layer, powered by Topline Pro, including calls and messages made using AI-powered technology. You can unsubscribe at any time by replying STOP. Message and data rates may apply. Message frequency varies.

By submitting this form, you agree to our Terms of Service & Privacy Policy.

Peeltex in New York and the Northeast

Peeltex Installer in New York

Peeltex is a water based, zero VOC peelable coating made in Belgium. First Layer sprays it on finished surfaces in New York City, on Long Island and across the Northeast, after hours, then peels it off in one sheet at turnover. Every Peeltex coating is temporary surface protection, peeled off at turnover.

  • Zero VOC
  • pH about 7
  • Made from recycled raw materials
  • Sold in 57 countries
Illustration of a gloved hand peeling a grey protective sheet off polished white marble
AI-generated illustration of Peeltex being peeled in one sheet.
What it is, who sells it, who installs it

Peeltex New York: one product, four hands

Peeltex NY work starts with a plain fact. First Layer does not make Peeltex and does not sell it. We install it. Peeltex Long Island and Northeast jobs follow the same chain, so you always know who to call for what.

It sprays on as a milky liquid and dries to a flexible film. At turnover it peels off in one sheet. Need the product for your own crew? Strata Shield Supply sells it. Want it applied? That is us.

  • Water based, zero VOC coating
  • Neutral pH, about 7
  • Made from recycled raw materials
  • Sold in 57 countries
  1. PeeltexMade in Belgium. The brand and the coating.
  2. The North American importerSpray Shield brings Peeltex to North America.
  3. Strata Shield SupplySells the product. Call to order.
  4. First LayerInstalls it, after hours, and peels it at handover.

Want to apply it yourself?

Strata Shield Supply sells Peeltex. Call to order.

Visit Strata Shield Supply
Four coatings

Which Peeltex goes where

Each coating has one job. Use the wrong one and the film fails, so we match the coating to the surface before we spray.

Peeltex Clear

Dries clear, so the finish stays visible.

Where it goes

  • Interior glass and mirrors
  • Stainless steel and fixtures
  • Elevator buttons and operating panels
  • Polished marble and stone
  • Finished surfaces, dry areas only

Where it doesn't

  • Exterior or wet areas
  • Porous surfaces

Peeltex Grey

Touch dry in about 2 hours.

Where it goes

  • Finished interior floors, with fine sand or glass dust broadcast into the wet coat for traction
  • Polished marble, terrazzo and polished stone
  • Elevator cab walls, floors, sills and tracks
  • Loading docks and steel plates, with fine grit

Where it doesn't

  • Carpet, unless carpet protection is down first
  • Fabrics and fresh paint
  • Heavy loads on its own

Peeltex White

Bright white, easy to see and to clean.

Where it goes

  • Paint booths and overspray areas
  • Elevator cab walls, floors, sills and tracks
  • Stage floors

Where it doesn't

  • Bare porous surfaces
  • Carpet, unless carpet protection is down first
  • Heavy loads on its own

Peeltex High Humidity

The exterior coating. About 12 months.

Where it goes

  • Exterior glass and frames
  • Facade work, install to handover
  • Concrete and precast, after a moisture test

Where it doesn't

  • Fabrics
  • Bare brick and untreated wood
  • Past about 12 months
  • Fresh paint or flaking surfaces

Polished marble and polished stone are approved. Historic or landmark finishes still get a test patch if the conservator asks for one. Carpet gets Koruser or Axiom carpet protection first, then Peeltex over it. See the full list on where Peeltex doesn't go, and how a job runs on how it works.

Peeltex vs board

Peeltex or hardboard on a finished floor?

An honest comparison. Both have a place, and they do different jobs.

Hardboard

  • Can shift under carts and lifts
  • Seams open up
  • Lets water and dust get underneath
  • Moisture can sit trapped under it

Peeltex

  • Sprayed on as a liquid, so no loose boards
  • Sealed, so spills stay on top where the crew can see them
  • Peels off in one sheet
  • No impact rating on its own

Where heavy loads or dropped tools are expected, Peeltex alone is not impact protection. We use felt-back impact board with a sealed Peeltex Grey top. See the packages.

Questions

Peeltex questions, answered

What is Peeltex?

Peeltex is a water based peelable coating made in Belgium. It sprays on as a liquid, dries to a flexible film and peels off in one sheet. It is zero VOC, has a pH of about 7 and is made from recycled raw materials. First Layer installs it in New York, on Long Island and across the Northeast.

Where does Peeltex go?

It depends on the coating. Clear goes on interior glass, mirrors, stainless, fixtures and elevator buttons and operating panels, in dry areas. Grey goes on finished interior floors, polished marble and stone, elevator cab walls, floors, sills and tracks, and loading docks and steel plates with fine grit. White goes in paint booths and on elevator cab walls and floors. High Humidity goes outside on glass and frames, and on concrete and precast after a moisture test. Carpet gets carpet protection first, then Peeltex over it. Fabrics, freshly painted surfaces, bare brick, untreated wood and other porous surfaces are not coated directly.

How long does Peeltex stay on?

It depends on the coating. Peeltex Clear is for interior, dry areas only. Peeltex High Humidity is the exterior coating and stays on about 12 months. We do not publish a duration for the others. Tell us the surface and the schedule at the site walk, and we test a patch before we spray.

Who installs Peeltex in New York?

First Layer installs it. We spray Peeltex on finished surfaces before the work starts, inspect it during the job and peel it off in one sheet at turnover. We work after hours, so the building, the crew or the production never waits. We serve New York City, Long Island and the Northeast.

Where do I buy Peeltex?

Strata Shield Supply sells Peeltex. It is a separate company from First Layer, and you call to order. If you would rather not apply it yourself, First Layer installs it. Book a site walk and we will look at your surfaces and tell you which coating fits.

Next step

Book a site walk

Tell us the building and the surfaces. We pick the coating, test a patch and schedule the install after hours. Questions first? See how it works or the packages.